Log Splitter Control Valve Sticking

Hydraulic fluid is really the main component in your log splitter. Anyone ever rebuild a log splitter hydaulic valve?

Buy Ruggedmade Energy Hydraulic Log Splitter Control Valve 0c000908 Online In Indonesia B01gd729ie

• rated for 3000 psi (207 bar).

Log splitter control valve sticking. Use and care of kick off valve 1. I have a brave log splitter and the last few weeks the detent/spoil valve has become sticky after the i split a couple of hours. Remove #5 cotter pin and #4 clevis pin to disconnect the #3 control lever from the #2 valve spool.

Result in high back pressure and sticking spools. When it retracts it pulls in tight and stalls the engine. If playback doesn't begin shortly, try restarting your device.

Made design improvements and upgrades to its log splitter valve detent assembly in 2008. Other than that it works fine. The ball (like a ball bearing) moves in and out if you push on it and the.

This valve is the most prevalent valve used in the residential log splitter industry. This tutorial apply to the energy control valve. If the valve has the name “energy” on the end cap, as shown in figure 3, the valve must be tested.

If you're used to the lever going one way on one log splitter, you might have overlooked the valve position on a different log splitter that works differently. Push handle in to retract and the detent will hold the handle. Used to the lever going one way on one log splitter, you might have overlooked the valve position on a different log splitter that works differently.

And now it started to stick going out and it will go out to the end and stall the engine. On one side of the valve there is a inch long bolt (only way i know how to describe it) with a ball in the end. The hydraulic pump controls the flow of fluid within the pump system.

If the valve is sticking in the retract position and not returning to center like it should at the completion of the stroke, then that usually indicates something in the valve spool, or the detent assembly, is hanging up. First, don’t forget there is direct correlation between your machines working power and the hydraulic fluid level. If the oil is found to be enough then the problem is due to the air mixed with liquid when opening the bleed valve and cycling pressure plate.

My next solution is to replace the entire valve assembly for about $60 because it's leaking slowly in three places. Remove the air from the system to solve this problem and keep the bleed valve tightened enough. Hydraulic fluid that is cold or dirty prevents the control valves handle from returning to position.

In temperatures below 32f, extend and retract the wedge several times to warm up the fluid before splitting logs. It's a huskee 22 ton and the valve is sticking both ways. You can try adjusting the relief to a lower setting and see if that cures the control valve sticking.

Failed hydraulic valve seals around the log splitter's actuator rod can cause hydraulic fluid to leak out of the valve body. The detent kit allows for your handle to stay engaged while retracting your log splitter cylinder to the start position. Why won't the control valve handle on my log splitter snap back to the neutral position when i release it?

The valve will eventually fail to apply hydraulic fluid pressure to the hydraulic cylinder to extend the wedge. Maximize device performance and safety by using the device for its Ls directional control valves installation & user guide.

Mounting, adjustment & assembly instructions: Don’t let the level get low and check it frequently. Do not force a device or attachment to do the work of a larger industrial device.

Check the manual to be sure you have proper lever position. Use the correct device for the job. Locate the control valve at the operator’s position of the log splitter and look at the control valve end cap (opposite end from the control handle).

In a typical log splitter, the operator places a log on the splitter, then shifts a directional valve to route fluid from the pump to the cap end of the hydraulic cylinder. Pull handle out to extend cylinder. Do not use this device if the valve spool does not center or appears to stick.

Handle is spring loaded, and will return to neutral when released. Replace the hydraulic control valve when you see fluid leaking out of the valve body. I think i can hold off until spring.

The control valves works by allowing a pressure buildup to automaticly center the valve. Check the pressure going into the detent valve. Check the manual to be sure you have proper lever position.

Also it is hard to trip the lever to get it to stop retracting. If your pump is not making enough pressure to center the control valve, then it would just set there and dead head without releasing automaticly. You need to check the amount of oil first.

This allows for faster wood splitting cycles when operating your log splitter. A detent valve lever can be pushed up or down to put the valve into operation. The combined flow from both pumps extends the cylinder's piston rapidly to reduce the.

Push the #2 valve spool all the way out the detent end of the valve body. Check the position of the lever. Inlet/outlet 3/4” npt and work ports 1/2” npt.

Read about gas log splitter.

25 Fix Log Splitter Hydraulic Control Valve O-ring Rebuild - Youtube

New Prince 2 Two Spool Log Splitter Detent Valve W Log Lift Rd522ccae5a4b1 Ebay